Engineering/Engineering Electrical Engineering Dc Motors part3 Sample Test,Sample questions

Question:
D.C. generators are installed near the load centres to reduce

1.iron losses

2.line losses

3.sparking

4.corona losses


Question:
D.C. generators are normally designed for maximum efficiency around

1.full-load

2.rated r.p.m.

3.rated voltage

4.all of the above


Question:
D.C. motor is to a drive a load which is almost nil for certain part of the load cycle and peak value for short duration. We will select this

1.series motor

2.shunt motor

3.compound motor

4.any of the above


Question:
D.C. motor is to drive a load which has certain minimum value for most of the time and some peak value for short duration. We will select the

1.series motor

2.shunt motor

3.compound motor

4.any of the above


Question:
For constant torque drive which speed control method is preferred ?

1.Field control

2.Armature voltage control

3.Shunt armature control

4.Mechanical loading system


Question:
Hopkinson s test on D.C. machines is conducted at

1.no-load

2.part load

3.full-load

4.overload4


Question:
If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens

1.this will make armature to take heavy current possibly burning it

2.this will result in excessive speed possibly destroying armature due to excessive

3.centrifugal stresses

4.nothing will happen to motormotor will come to stop


Question:
If the terminals of armature of D.C. motor are interchanged this action will offer following kind of braking (o) regenerative

1.plugging

2.dynamic braking

3.none of the above

4.any of the above


Question:
In a D.C. generator all of the following could be the effects of iron losses except

1.Loss of efficiency

2.Excessive heating of core

3.Increase in terminal voltage

4.Rise in temperature of ventilating air


Question:
In a D.C. generator the iron losses mainly take place in

1.yoke

2.commutator

3.armature conductors

4.armature rotor


Question:
In a manual shunt motor starter

1.over load relay is connected in series and no volt relay in parallel with the load

2.over load relay is connected in paral?lel and no volt relay in series with the load

3.over load relay and no volt relay are both connected in series with the load

4.over load relay and no volt relay are both connected in parallel with the load


Question:
In the D.C. motor the iron losses occur in

1.the field

2.the armature

3.the brushes

4.the commutator


Question:
In variable speed motor

1.a stronger commutating field is needed at low speed than at high speed

2.a weaker commutating field is needed at low speed than at high speed

3.same commutating field is needed at low speed than at high speed

4.none of the above is correct


Question:
One D.C. motor drives another D.C. motor. The second D.C. motor when excited and driven

1.runs as a generator

2.does not run as a generator

3.also runs as a motor comes to stop after sometime

4.also runs as a motor comes to stop after sometime


Question:
The condition for maximum efficiency for a D.C. generator is

1.eddy current losses = stray losses

2.hysteresis losses = eddy current losses

3.copper losses = 0

4.variable losses = constant losses


Question:
The hysteresis loss in a D.C. machine least depends on

1.Frequency of magnetic reversals

2.Maximum value of flux density

3.Volume and grade of iron

4.Rate of flow of ventilating air


Question:
The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?

1.hysteresis loss

2.field copper loss

3.armature copper loss

4.eddy current loss


Question:
The plugging gives the

1.zero torque braking

2.smallest torque braking

3.highest torque braking

4.none of the above


Question:
The purpose of retardation test on D.C. shunt machines is to find out

1.stray losses

2.eddy current losses

3.field copper losses

4.windage losses


Question:
The speed of a D.C. shunt motor is required to be more than full load speed. This is possible by

1.reducing the field current

2.decreasing the armature current

3.increasing the armature current

4.increasing the excitation current


Question:
When the armature of a D.C. motor rotates e.m.f. induced is

1.self-induced e.m.f.

2.mutually induced e.m.f.

3.back e.m.f.

4.none of the above


Question:
Where D.C. motor of H.P. 12 or more requires frequent starting stopping reversing and speed control

1.drum type controller is used

2.three point starter is used

3.four point starter is used

4.all above can be used


Question:
Which D.C. motor has got maximum self relieving property ?

1.Series motor

2.Shunt motor

3.Cumulatively compounded motor

4.Differentially compounded motor


Question:
Which method of braking is generally used in elevators ?

1.Plugging

2.Regenerative braking

3.Rheostatic braking

4.None of the above


Question:
Which motor should not be started on no-load ?

1.Series motor

2.Shunt motor

3.Cumulatively compounded motor

4.Differentially compounded motor.


Question:
Which of the following loss in a D.C. generator is dissipated in the form of heat?

1.Mechanical loss

2.Core loss

3.Copper loss

4.All of the above


Question:
Which of the following losses are significantly reduced by laminating the core of a D.C. generator ?

1.Hysteresis losses

2.Eddy current losses

3.Copper losses

4.Windage losses


Question:
Which of the following steps is likely to result in reduction of hysteresis loss in a D.C. generator ?

1.Providing laminations in armature core

2.Providing laminations in stator

3.Using non-magnetic material for frame

4.Using material of low hysteresis co-efficient for armature core material


Question:
Why are the D.C. motors preferred for traction applications ?

1.Torque and speed are inversely proportional to armature current

2.Torque is proportional to armature current

3.Torque is proportional to square root of armature current

4.The speed is inversely proportional to the torque and the torque is proportional to square of armature current


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!