Engineering/Electric Drives MCQ Questions and Answers Sample Test,Sample questions

Question:
 A 3-phase induction machine draws active power P and reactive power Q from the grid. If it is operated as a generator then P and Q will be _________

1.Positive and Negative

2.Negative and Positive

3.Positive and Positive

4.Negative and Negative


Question:
 At low values of slip the electromagnetic torque is directly proportional to ___________

1.s

2.s2

3.s3

4.s4


Question:
 Calculate the total heat dissipated in a rotor resistor of 14.23 ? when .65 A current flows through it.

1.6.45 W

2.6.01 W

3.6.78 W

4.6.98 W


Question:
 If induction motor air gap power is 2 KW and mechanically developed power is 1 KW then rotor ohmic loss will be _________ KW.7. 

1.1

2.2

3.3

4.4


Question:
 If induction motor air gap power is 48 KW and gross developed power is 28 KW then rotor ohmic loss will be _________ KW.

1.10

2.20

3.30

4.40


Question:
 In the rotor voltage injection method when an external voltage source is in phase with the main voltage then speed will ___________

1.Increase

2.Decrease

3.Remain unchanged

4.First increases then decrease


Question:
 The slope of the V-I curve is 1.1�. Calculate the value of resistance. Assume the relationship between voltage and current is a straight line.

1..019 ?

2..036 ?

3..075 ?

4..084 ?


Question:
 What is the formula for the maximum active power in the cylindrical rotor synchronous machine? (Eb represents armature emf Vt represents terminal voltage ? represents rotor angle X represents reactance)

1.Eb�Vt�sin?�X

2.Eb�Vt2�X

3.Eb2�Vt�sin?�X

4.Eb�Vt�X


Question:
A 16-pole 3-phase 60 Hz induction motor is operating at a speed of 150 rpm. The frequency of the rotor current of the motor in Hz is __________

1.20

2.40

3.30

4.10


Question:
A 2-pole 3-phase ______ Hz induction motor is operating at a speed of 550 rpm. The frequency of the rotor current of the motor in Hz is 2.

1.9.98

2.9.71

3.9.12

4.9.37


Question:
A 20-pole 3-phase 90 Hz induction motor is operating at a speed of _______ rpm. The frequency of the rotor current of the motor in Hz is 20.

1.418.56

2.420.12

3.421.23

4.422.45


Question:
A 32-pole 3-phase 70 Hz induction motor is operating at a speed of 112 rpm. The frequency of the rotor current the motor in Hz is __________

1.40.2

2.46.1

3.40.1

4.40.6


Question:
Calculate mark to space ratio if the system is on for 26.3 sec and off for 24.2 sec.

1.1.086

2.1.042

3.1.214

4.1.876


Question:
Calculate mark to space ratio if the system is on for 4.3 sec and off for 78.2 sec.

1.0.054

2.0.047

3.0.039

4.0.018


Question:
Calculate the active power in a .154 H inductor.

1.22 W

2.14 W

3.45 W

4.0 W


Question:
Calculate the active power in a .89 H inductor.

1.1.535 W

2.0 W

3.2.484 W

4.1.598 W


Question:
Calculate the active power in a 168.12 H inductor.

1.65 W

2.0 W

3.68 W

4.64 W


Question:
Calculate the active power in an 8.12 F capacitor.

1.89 W

2.41 W

3.0 W

4.48 W


Question:
Calculate the amplitude of the sinusoidal waveform 

1.710

2.715

3.716

4.718


Question:
Calculate the amplitude of the sinusoidal waveform z(t)=.27sin(.369?t+.142?�4.25).

1.0.287

2.0.27

3.0.287

4.0.216


Question:
Calculate the average value of the sinusoidal waveform x(t)=848sin(1.65?t+2?�0.68).

1.0

2.78 V

3.15 V

4. 85 V


Question:
Calculate the condition for maximum voltage regulation in the synchronous machine.

1.?=?s

2.?=2?s

3.?=4?s

4.?=8?s


Question:
Calculate the line current in the delta connection when phase current=17 A.

1.29.44 A

2.24.64 A

3.23.48 A

4.26.56 A


Question:
Calculate the line voltage in star connection when phase voltage=45 V.

1.77.9 V

2.77.6 V

3.77.2 V

4.77.8 V


Question:
Calculate the line voltage in the delta connection when phase voltage=45 V.

1.46 V

2.47 V

3.45 V

4.78 V


Question:
Calculate the maximum value of slip when rotor resistance is 2 ? and rotor reactance is 3 ?.

1.0.66

2.0.33

3.0.44

4.0.99


Question:
Calculate the moment of inertia of the sphere having a mass of 8.4 kg and radius of 61 cm.

1.3.124 kgm2

2.3.125 kgm2

3.4.545 kgm2

4.5.552 kgm2


Question:
Calculate the peak value of sinusoidal waveform if the r.m.s value is 21 V.29.69 V

1.29.69 V

2.48.74 V

3.69.23 V

4.25.74 V


Question:
Calculate the power factor angle during the resonance condition.

1.0�

2.10�

3.80�

4.90�


Question:
Calculate the power factor if the power angle is 36.86�.

1.0.8

2.0.4

3.0.6

4.1


Question:
Calculate the reactive power in a 2.2 ? resistor.

1.1.5 VAR

2.2.6 VAR

3.0 VAR

4.1.9 VAR


Question:
Calculate the reactive power in a 7.2545 ? resistor.

1.1.221 VAR

2.2.611 VAR

3.0 VAR

4.1.997 VAR


Question:
Calculate the time period of the waveform i(t)=sin(?t+6?�4)+sin(?t+5?�6).

1.2 sec

2.4 sec

3.5 sec

4.3 sec


Question:
Calculate the time period of the waveform v(t)=12sin(8?t+8?�15)+144sin(2?t+?�6)+ 445sin(?t+7?�6).

1.8 sec

2.4 sec

3.7 sec

4.3 sec


Question:
Calculate the time period of the waveform z(t)=24sin(?t+?�4)+4sin(2?t+?�6).

1.2 sec

2.3 sec

3.4 sec

4.1 sec


Question:
Calculate the total heat dissipated in a resistor of 44 ? when 0 A current flows through it.

1.0 W

2.2 W

3.1.5 W

4..3 W


Question:
Calculate the total heat dissipated in a resistor of 50 ? when 1.4 A current flows through it.

1.98 W

2.92 W

3.91 W

4.93 W


Question:
Calculate the total heat dissipated in a rotor resistor of 21 ? when .81 A current flows through it.

1.13.77 W

2.12.56 W

3.46.45 W

4.13.98 W


Question:
Calculate the value of the duty cycle if the system is on for 1 sec and off for 0 sec.1

1.1

2.0.4

3.0.1

4.0.6


Question:
Calculate the value of the duty cycle if the system is on for 5 sec and off for inf sec.12. 

1.0

2.0.4

3.0.2

4.0.1


Question:
Calculate the value of the frequency of the AC supply in India.

1.0 Hz

2.50 Hz

3.49 Hz

4.60 Hz


Question:
Calculate the value of the time period if the frequency of the signal is .07 sec.

1.14.28 sec

2.14.31 sec

3.14.23 sec

4.14.78 sec


Question:
Calculate the voltage regulation in the synchronous machine if the no-load voltage is 12 V and the full load voltage is 15V.

1.-20%

2.-40%

3.-60%

4.-80%


Question:
If induction motor air gap power is 1.8 KW and gross developed power is .1 KW then rotor ohmic loss will be _________ KW.

1.1.7

2.2.7

3.3.7

4.4.7


Question:
If induction motor air gap power is 10 KW and mechanically developed power is 8 KW then rotor ohmic loss will be _________ KW.

1.1

2.2

3.3

4.4


Question:
If induction motor air gap power is 67 KW and mechanically developed power is 26 KW then rotor ohmic loss will be _________ KW.

1.41

2.42

3.43

4.44


Question:
If induction motor rotor power is 157.5 KW and gross developed power is 79.9 KW then rotor ohmic loss will be _________ KW.

1.77.5

2.77.6

3.76.9

4.77.1


Question:
If induction motor rotor power is 157.5 KW and gross developed power is 79.9 KW then rotor ohmic loss will be _________ KW.

1.77.5

2.77.6

3.76.9

4.77.1


Question:
In a DC series motor the e.m.f developed is proportional to _______

1.N�Ia

2.N�Ia2

3.N�Ia3

4.N�Ia.5


Question:
In a DC shunt motor the e.m.f developed is proportional to ___________

1.Ia

2.Ia2

3.Ia3

4.Iao


Question:
In the chopper circuit commutation times are _______

1.Current commutation is equal to voltage commutation

2.Current commutation is less as compared to that of voltage commutation

3.Current commutation is more as compared to that of voltage commutation

4.Both commutation techniques are not comparable


Question:
In the rotor voltage injection method when an external voltage source is in opposite phase with the main voltage then speed will ___________

1.Increase

2.Decrease

3.Remain unchanged

4.First increases then decrease


Question:
R.M.S value of the periodic square waveform of amplitude 72 V.

1.72 V

2.56 V

3.12 V

4.33 V


Question:
R.M.S value of the sinusoidal waveform q(t)=2.11cos(87.25t+78?�478.23).

1.1.49 V

2.1.56 V

3.1.12 V

4.1.78 V


Question:
R.M.S value of the sinusoidal waveform v(t)=211sin(7.25t+7?�78.3).

1.149.19 V

2.156.23 V

3.116.57 V

4.178.64 V


Question:
R.M.S value of the sinusoidal waveform V=48sin(6.5?t+89?�46.8).

1.33.94 V

2.33.56 V

3.33.12 V

4.33.78 V


Question:
The advantage of the double squirrel cage induction motor over a single cage rotor is that its _______

1.Efficiency is higher

2.Power factor is higher

3.Slip is larger

4.Starting current is lower


Question:
The generated e.m.f from 4-pole armature having 1 conductors driven at 1 rev/sec having flux per pole as 10 Wb with wave winding is ___________

1.30 V

2.40 V

3.70 V

4.20 V


Question:
The most suitable control-motor application is __________

1.AC shunt motor

2.DC separately motor

3.AC one-phase induction motor

4.DC shunt motor


Question:
The no-load circuit test on a 3-? induction motor is conducted at a rotor speed of _______

1.Zero

2.< Ns

3.> Ns

4.Ns


Question:
The phase difference between voltage and current in the choke coil.

1.90�

2.40�

3.50�

4.68�


Question:
The power factor of a squirrel cage induction motor generally is ___________

1..6-.8

2..1-.2

3..2-.4

4..5-.7


Question:
The power factor of a squirrel cage induction motor is ___________

1.Low at light load only

2.Low at heavy loads only

3.Low at the light and heavy loads both

4.Low at rate load only


Question:
The power factor of a squirrel cage induction motor is ___________

1.High at light load only

2.High at heavy loads only

3.Low at the light and heavy loads both

4.Low at rate load only


Question:
The short circuit test on a 3-? induction motor is conducted at a rotor speed of _______

1.Zero

2.< Ns

3.> Ns

4.Ns


Question:
The slope of the V-I curve is 13.89�. Calculate the value of resistance.

1..247 ?

2..345 ?

3..231 ?

4..222 ?


Question:
The slope of the V-I curve is 180o. Calculate the value of resistance. The graph is parallel to the x-axis.9. 

1.1.47 ?

2.1.81 ?

3.0 ?

4.4.12 ?


Question:
The slope of the V-I curve is 35.48�. Calculate the value of resistance. Assume the relationship between voltage and current is a straight line.

1.0.452 ?

2.0.462 ?

3.0.752 ?

4.0.712 ?


Question:
The slope of the V-I curve is 39.1�. Calculate the value of resistance. Assume the relationship between voltage and current is a straight line.

1..81 ?

2..36 ?

3..75 ?

4..84 ?


Question:
The slope of the V-I curve is 9.1�. Calculate the value of resistance. Assume the relationship between voltage and current is a straight line.

1.16 ?

2.26 ?

3.25 ?

4.44 ?


Question:
The value of slip at which maximum torque occurs ________

1.R2�X2

2.4R2�X2

3.2R2�X2

4.R2�3X2


Question:
What is the unit of the distance?

1.m

2.m/s

3.atm/m

4.Volt


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!