Engineering/Civil Engineering MCQS-Surveying Section 8 Sample Test,Sample questions

Question:
  
In case of a double line river, contours are

1.stopped at the banks of the river

2.stopped at the edge of the river

3.drawn across the water

4.drawn by parabolic curves having their vertex at the centre of the water.


Question:
  
The representation of general topography of a very flat terrain is possible only

1.by drawing contours at large interval

2. by drawing contours at small interval

3.by giving spot levels at large interval

4.by giving spot levels to salient features at close interval.


Question:
  Pick up the correct statement from the following

1. the contour lines having the same elevation cannot unite and continue as one line

2. a contour can not end abruptly, but must ultimately close itself not necessarily within the limits of map.

3.the direction of steepest slope at a point on a contour is at right angles to the contour

4. all the above.


Question:
A transit is oriented by setting its vernier A to read the back azimuth of the preceding line. A back sight on the preceding transit station taken and transit is rotated about its vertical axis. The vernier A reads

1.azimuth of the forward line

2.bearing of the. forward line

3.back bearing of the forward line

4.equal to 360°-azimuth of the forward line.


Question:
Contours of different elevations may cross each other only in the case of

1.an over hanging cliff

2.a vertical cliff

3.a saddle

4.an inclined plane.


Question:
Correction per chain length of 100 links along a slope of α radians, is

1. 100 α2

2.100 α

3.100 α3

4.100 α-1.


Question:
Determining the difference in elevation between two points on the surface of the earth, is known as

1.levelling

2.simple levelling

3.differential levelling

4. longitudinal levelling.


Question:
During levelling if back sight is more than foresight

1.The forward staff is at lower point

2.The back staff is at lower point

3.The difference in level, cannot be ascertained.

4.none of these.


Question:
In case of a direct vernier scale

1.graduations increase in opposite direction in which graduations of the main scale increase

2.smallest division is longer than smallest division of the main scale

3.graduations increase in the same direction in which graduations of the main scale increase

4.none of these.


Question:
In geodetic surveys higher accuracy is achieved, if

1. curvature of the earth surface is ignored

2.curvature of the earth surface is taken into account

3.angles between the curved lines are treated as plane angles

4.none of these.


Question:
In geodetic surveys higher accuracy is achieved, if

1.curvature of the earth surface is ignored

2. curvature of the earth surface is taken into account

3.angles between the curved lines are treated as plane angles

4. none of these.


Question:
A transit is oriented by setting its vernier A to read the back azimuth of the preceding line. A back sight on the preceding transit station taken and transit is rotated about its vertical axis. The vernier A reads

1.The directions of plumb lines suspended at different points in a survey are not strictly parallel

2. In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal

3.In surveys of large extent, the effect of curvature of the earth must be considered

4.All the above.


Question:
Permanent adjustments of a level are

1.2 in number

2.3 in number

3.4 in number

4.6 in number


Question:
The bearing of line AB is 152° 30' and angle ABC measured clockwise is 124° 28'. The bearing of BC is

1.27° 52'

2.96° 58'

3. 148° 08'

4.186° 58'


Question:
The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is

1.5.73°

2.5.37°

3.3.57°

4.3.75°.


Question:
The surface of zero elevation around the earth, which is slightly irregular and curved, is known as

1.mean sea level

2.geoid surface

3.level surface

4. horizontal surface.


Question:
Two contour lines, having the same elevation

1. cannot cross each other

2.can cross each other

3.cannot unite together

4.can unite together.


Question:
While working on a plane table, the correct rule is :

1.Draw continuous lines from all instrument stations

2.Draw short rays sufficient to contain the points sought

3.Intersection should be obtained by actually drawing second rays

4. Take maximum number of sights as possible from each station to distant objects.


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!