Engineering/Civil Engineering -MCQS-Hydraulics Section 3 Sample Test,Sample questions

Question:
 
Cappoletti weir is a

1. rectangular weir whose length is kept 3 times the height of the water above sill

2. triangular weir whose notch angle is 90°

3.trapezoidal weir, whose sides slope 1 horizontal to 2 verticals

4.a combination of rectangular and triangular weirs.


Question:
 
Discharge over an ogee weir remains the same as that of

1.sharp crested weir

2. triangular weir

3.cippoletti weir

4.drowned weir.


Question:
 
If velocities of fluid particles vary from point to point in magnitude and direction, as well as from instant to instant, the flow is said to be

1.laminar

2.turbulent flow

3.uniform flow

4.non-uniform flow.


Question:
 
Most economical section of a triangular channel, is

1.equilateral triangle

2.right angled triangle

3.isosceles triangle with 45° vertex angle

4. right angled triangle with equal sides.


Question:
 
Piezometers are used to measure

1.pressure in water channels, pipes etc.

2.difference in pressure at two points

3.atmospheric pressure

4.very low pressure.


Question:
 
The ratio of frictional factor and coefficient of friction used in general equation for a head loss in a pipe, is

A. 1

1.1

2.2

3.3

4.4


Question:
 
To avoid an interruption in the flow of a syphon, an air vessel is provided

1.at the inlet

2.at the outlet

3.at the summit

4.at any point between intet and outlet.


Question:
  
A non-uniform steady flow is through

1.a long tube at a decreasing rate

2.an expanding tube at constant rate

3.an expanding tube at increasing rate

4.a long pipe at increasing rate.


Question:
  
Flow in pipes is turbulent if Reynold number is

1.less than 2100

2.more than 3000

3. between 2100 and 3000

4.none of these.


Question:
  
Fluids change the volume under external presssure due to

1.plasticity

2.viscosity

3.compressibility

4. none of these.


Question:
  
For maximum horse power of a nozzle, the head supplied must be equal to

1. head loss in the pipe due to friction

2.twice the head loss in the pipe due to friction

3. thrice the head loss in the pipe due to friction

4.four times the head loss in the pipe due to friction.


Question:
  
Manometers are used to measure

1. pressure in water channels, pipes etc.

2.difference in pressure at two points

3.atmospheric pressure

4.very low pressure.


Question:
  
The rise of the liquid along the walls of a revolving cylinder above the initial level, is

1.greater than the depression of the liquid at the axis of rotation

2.lesser than the depression of the liquid at the axis of rotation

3. the same as the depression of the liquid at the axis of rotation

4.none of these.


Question:
  
Uniform flow is said to occur when

1.size and shape of the cross-section in a particular length remain constant

2.size and shape of the cross-section change along a length

3.frictional loss in the particular length of the channel will the more than the drop in its elevation

4. frictional loss in the particular length of the channel, will be less than the drop in elevation.


Question:
A fluid particle may possess the displacement of

1.translation

2.rotation

3.distortion

4.all the above.


Question:
A jet projected at an angle of 45θ, 40 m from the foot of a vertical column, just reaches the top of the column. The height of the column is

1.15 m

2.20 m

3.30 m

4.40 m


Question:
An ideal fluid is

1.incompressible

2.compressible

3.compressible and non-viscous

4.slightly affected by surface torque.


Question:
Atmospheric pressure is equal to water column head of

1.9.81 m

2.5.0 m

3.10.30 m

4.7.5 m.


Question:
Atmospheric pressure varies with

1.altitude

2.temperature

3.weather conditions

4.all of the above.


Question:
Back water curve is caused if

1. friction head loss is more than the bed slope

2.pressure is due to weir in the channel

3.there is an increase in width of the channel

4.none of these.


Question:
For exerting a pressure of 4.8 kg/cm2, the depth of oil (specific gravity 0.8), should be

1.60 cm

2.56 cm

3.40 cm

4.41 cm


Question:
For the flow of liquid from an open ended tube (or nozzle) leading to the formation of spray of liquid drops, the number generally applied, is

1.Froude number

2.Weber number

3.Reynold number

4.Mach number.


Question:
In an open tube, free surface of mercury remains

1.horizontal

2.curved upwards

3.curved downwards

4. none of these.


Question:
Manning's formula is used for

1.flow in open channels

2.head loss due to friction in open channels

3.head loss due to friction in pipes flowing full

4.flow in pipes.


Question:
Molecules of fluids get attracted due to

1.capillarity action

2.surface tension

3.adhesion

4.cohesion


Question:
On an inclined plane, centre of pressure is located

1.at the centroid

2.above the centroid

3.below the centroid

4.anywhere.


Question:
Pick up the correct statement from the following :

1.Total energy gradient is the graphical representation of the total head at any section of a pipe line

2.Vertical distance between the total energy line and hydraulic grade line is equal to the velocity head

3.Vertical distance between the total energy line and total energy gradient represents loss of head

4.all the above.


Question:
Pick up the correct statement from the following :

1.When the length of the tube is equal to diameter of the internal mouth piece, the jet of liquid comes out without touching the sides of the tube

2.When the length of the tube is three times the diameter of the internal mouth piece, the jet diameter is equal to diameter of the tube.

3.both (a) and (b)

4. Neither (a) nor (b).


Question:
Power transmitted through a pipe is maximum when friction head loss, is

1.one-half of the total head supplied

2. one-third of the total head supplied

3.one-fouth of the total head supplied

4.equal to the total head supplied.


Question:
Shear stress is directly proportional to

1. the velocity

2.the shear strain

3.the viscosity

4.the velocity.


Question:
Specific weight of liquid

1. remains constant at every place

2. does not remain constant at every place

3. varies from place to place on the earth

4.does not vary on any other planet.


Question:
The best side slope for most economical trapezoidal section, is

1.30°

2.45°

3.60°

4. none of these.


Question:
The following is not a laminar flow

1.Flow of oil in measuring instruments

2.Flow in beds in ground water

3.Rise of water in plants through roots

4.Flow in water pipe lines.


Question:
The magnitude of water hammer in a pipe depends upon

1.speed at which value is closed

2.length of the pipe line

3.elastic properties of the following liquid

4.all the above


Question:
The specific weight of water is 1000 kg/m3

1. at normal pressure of 760 mm

2.at 4°C temperature

3.at mean sea level

4.all the above.


Question:
To avoid vapourisation, pipe lines are laid over the ridge so that these are above the hydraulic gradient line, not more than

1.2.4 m

2.6.4 m

3.10.0 m

4.5.0 m


Question:
When no air is left below the nappe and water stream adheres to the down stream face of the weir, it is known as

1. free nappe

2.depressed nappe

3.clinging nappe

4. none of these.


Question:
Which one of the following statements is true ?

1. The value of kinetic energy correction factor for turbulent flow lies between 1.03 to 1.06

2.The value of kinetic energy correction factor for laminar flow is 2

3.The practical value of kinetic energy correction factor for turbulent flow is unity

4.all the above.


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!