Engineering/Civil -MCQ RCC Structures Design - Section 2 Sample Test,Sample questions

Question:
 
In a singly reinforced beam, the effective depth is measured from its compression edge to

1.tensile edge

2. tensile reinforcement

3.neutral axis of the beam

4.longitudinal central axis.


Question:
 
The maximum diameter of a bar used in a ribbed slab, is

1.12 mm

2.6 mm

3.20 mm

4.22 mm


Question:
 
The toe projection of foundation slabs is taken

1.as one third of the base

2.as one sixth of overall height of the wall

3.equal to heel slab

4. below ground surface.


Question:
  
A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is

1.30

2.35

3.40

4.45


Question:
  
If the depth of actual neutral axis of a doubly reinforced beam

1.is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier

2.is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier

3.is equal to the depth of critical neutral axis, the concrete and steel attain their maximum stresses simultanesouly

4.all the above.


Question:
  
If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than

1.4 mm

2.5 mm

3.6 mm

4.8 mm


Question:
  
If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2, the length of the beam having nominal reinforcement, is

1.4 cm

2.6 m

3.8 m

4.10 m


Question:
  
If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a

1.simply supported beam

2.continuous beam

3.cantilever beam

4.none of these.


Question:
  
In a simply supported slab the minimum spacing of distribution reinforcement, should be four times the effective thickness of the slab or

1.20 cm

2. 30 cm

3.40 cm

4. 60 cm


Question:
  
Pick up the incorrect statement from the following The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to

1.shear force

2.area of the section

3.distance of the C.G. of the area from its neutral axis

4.moment of the beam section about its neutral axis


Question:
  
Steel beam theory is used for

1. design of simple steel beams

2.steel beams encased in concrete

3.doubly reinforced beams ignoring compressive stress in concrete

4. beams if shear exceeds 4 times allowable shear stress.


Question:
  
Steel beam theory is used for

1.design of simple steel beams

2. steel beams encased in concrete

3.doubly reinforced beams ignoring compressive stress in concrete

4.beams if shear exceeds 4 times allowable shear stress.


Question:
  
To ensure uniform pressure distribution, the thickness of the foundation, is

1.kept uniform throughout

2.increased gradually towards the edge

3.decreased gradually towards the edge

4.kept zero at the edge.


Question:
A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis

1. remains within the flange

2.remains below the slab

3.coincides the geometrical centre of the beam

4. none of these.


Question:
According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than

1.20 cm

2. 30 cm

3.40 cm

4. 50 cm


Question:
Distribution of shear intensity over a rectangular section of a beam, follows :

1. a circular curve

2.a straight line

3.a parabolic curve

4.an elliptical curve


Question:
Distribution reinforcement in a simply supported slab, is provided to distribute

1.load

2.temperature stress

3. shrinkage stress

4. all the above.


Question:
For stairs spanning horizontally, the minimum waist provided is

1.4 cm

2.6 cm

3.8 cm

4.12 cm.


Question:
If a rectangular prestressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be

1.5 cm

2.10 cm

3.15 cm

4.20 cm


Question:
If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2, the share stirrups are provided for a distance x from either end where x is

1. 50 cm

2.100 cm

3.150 cm

4.200 cm


Question:
If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is

1.0.50%

2.0.60%

3.0.70%

4.0.80%


Question:
If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by

1.0.2

2.0.3

3.0.4

4.0.5


Question:
o ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is

1.0.107 L

2. 0.207 L

3.0.307 L

4. 0.407 L


Question:
Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam

1.are curtailed if not required to resist the bending moment

2. are bent up at suitable places to serve as shear reinforcement

3.are bent down at suitable places to serve as shear reinforcement

4. are maintained at bottom to provide at least local bond stress.


Question:
Pick up the true statement from the following:

1.Plain ceiling provides the best property diffusing light

2. In the absence of beams, it is easier to install piping

3. In the absence of beams, it is easier to paint

4.All the above.


Question:
The advantage of reinforced concrete, is due to

1.monolithic character

2.fire-resisting and durability

3. economy because of less maintenance cost

4.All the above.


Question:
The horizontal portion of a step in a stairs case, is known as

1.rise

2.flight

3.winder

4.tread.


Question:
The length of lap in tension reinforcement should not be less than the bar diameter x (actual tension / four times the permissible average bond stress) if it is more than

1. 18 bar diameters

2.24 bar diameters

3.30 bar diameters

4.36 bar diameters


Question:
The length of the straight portion of a bar beyond the end of the hook, should be at least

1.twice the diameter

2.thrice the diameter

3.four times the diameter

4.seven times the diameter.


Question:
The maximum ratio of span to depth of a cantilever slab, is

1.8

2.10

3.12

4.14


Question:
The maximum shear stress (qmax) in a rectangular beam is

1.1.25 times the average

2.1.50 times the average

3.1.75 times the average

4. 2.0 times the average


Question:
The radius of a bar bend to form a hook, should not be less than

1.twice the diameter

2.thrice the diameter

3.four times the diameter

4.five times the diameter


Question:
The shear reinforcement in R.C.C. is provided to resist

1.vertical shear

2. horizontal shear

3.diagonal compression

4. diagonal tension.


Question:
The thickness of the topping of a ribbed slab, varies between

1.3 cm to 5 cm

2.5 cm to 8 cm

3.8 cm to 10 cm

4.12 cm to 15 cm


Question:
The toe projection of foundation slabs is taken

1.as one third of the base

2.as one sixth of overall height of the wall

3.equal to heel slab

4.below ground surface.


Question:
The weight of a foundation is assumed as

1.5% of wall weight

2. 7% of wall weight

3.10% of wall weight

4.12% of wall weight


Question:
Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of

1.h/4

2.h/3

3.h/2

4.2h/3


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!